Skil 2026 AA Manuel d'utilisateur télécharger pdf (Page 9)

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of the charger to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of the

charger, it must be disposed of safely and not

left unattended

USE

• Charging battery 0

- battery of new tools is not fully charged

- connect charger to power source as illustrated

- green light H will turn on indicating that the charger is

ready for operation

- insert battery into charger

- red light J will turn on indicating that the battery is

being charged

- after 3 hours the charging operation will be completed,

and the battery may be used, even though the red

light may still be on (the red light may require more

than 3 hours to turn o)

! remove battery from charger after charging

period has ended thereby lengthening the service

life of the battery

IMPORTANT:

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- ensure that the outside surface of the battery is clean

and dry before inserting into charger

- do not charge at temperatures below 0°C and over

40°C; this will seriously damage the battery as well as

the charger

- do not remove battery from tool while it is running

! a battery that is new or has not been used for a

longer period does not develop its full capacity

until after approximately 5 charging/

discharging cycles

- do not repeatedly recharge the battery after only a few

minutes of operation; this may result in a reduction of

operating time and battery eciency

- if you anticipate long periods of non-use for the tool, it

is best to unplug the charger from its power source

• On/o !

• Speed control for smooth starting @

• Changing direction of rotation #

- when not properly set in left/right position, switch A 2

cannot be activated

! change direction of rotation only when tool is at a

complete standstill

• Changing bits $

- insert the bit as deep as possible in the chuck

! do not use bits with a damaged shank

• Torque control (VariTorque) %

- limits the amount of output torque delivered by the

chuck (21 clutch settings)

- when turning in a screw, rst try VariTorque position 1

and increase until the desired depth has been reached

• Mechanical gear selection ^

- set selector E to desired speed

! actuate the gear selector only when tool is

switched off

LOW

- low speed

- high torque

- for screwdriving and drilling large diameters

- for tapping thread

HIGH

- high speed

- lower torque

- for drilling small diameters

• Holding and guiding the tool &

! while working, always hold the tool at the

grey-coloured grip area(s)

- keep ventilation slots F 2 uncovered

- do not apply too much pressure on the tool; let the tool

do the work for you

APPLICATION ADVICE

• Use the appropriate bits *

! only use sharp bits

• When drilling ferrous metals

- pre-drill a smaller hole, when a large hole is required

- lubricate drill bit occasionally with oil

• When turning in a screw at/near the cross cut end or an

edge of wood, pre-drill a hole in order to avoid cracking of

the wood

• For an optimal use of the tool a steady pressure on the

screw is required, especially while removing

• When screwdriving in hard wood one should pre-drill

a hole

• Splinterfree drilling in wood (

• Dustfree drilling in walls )

• Dustfree drilling in ceilings ¡

• Drilling in tiles without skidding ™

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Keep tool and charger clean

- clean charging contacts in charger with alcohol or

contact cleaner

! unplug charger from power source

before cleaning

• If the tool/charger should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool or charger undismantled together with

proof of purchase to your dealer or the nearest SKIL

service station (addresses as well as the service

diagram of the tool are listed on www.skil.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2002/96/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 131 132

Commentaires sur ces manuels

Pas de commentaire

Skil 2026 AA Manuel d'utilisateur Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Outils électriques Skil 2026 AA